General

Reloading, A Beginner’s Guide Part II

Electronic Scale

In the first installment of our series on reloading, we discussed the methods and procedures for cleaning, depriming, and reloading straight walled cases. In this article, we will discuss reloading bottle necked cartridges. Most necked down cartridges are rifle calibers, but there are a few notable exceptions, notably .357 Sig and Tokarev. The FN 5.7mm cartridge is bottle necked as well, but it is a proprietary round and is very difficult to properly (and safely) reload.

As with straight walled brass, make sure that your bottle necked brass is clean and free from debris. With bottle necked rifle brass, it’s generally a good idea to run your brass through a polisher. This cleans off powder residue as well as any dirt or corrosion from the brass. Make sure that once you are done polishing and cleaning your brass that there is no polishing media left on the outside or inside of the brass. Polishing and cleaning the brass helps make resizing much easier. Dirt, grit, or corrosion on your brass can scratch or damage your steel dies. Carbide dies don’t have this problem, but having nicely lubed clean brass means that you don’t have to pull so hard on the press lever when resizing.

Reloading bottle necked cartridges is actually fairly easy compared to reloading straight walled brass, but you do have to take the additional step of utilizing case lube. The primary difference between reloading straight walled cases and bottle neck cases is the resizing process. Bottle neck dies perform a lot of work with a single pull of the press lever. When resizing brass, the die not only resizes the case and deprimes the brass, it also has an expander ball that is plunged down the neck of the case so that new bullets can be seated.

When lubing your rifle brass, it is critically important to spray your case lube all around the outside as well as down the case mouth. This lubes the inside of the case for the expander ball. To properly lube the cases, set them all in a loading block with the mouth of the case up. Spray the cases on one side and from above at an angle so that the lubricant not only goes on the outside but also sprays down inside the neck. Turn the loading block so that all 360 degrees of the cases get lubed. Don’t be afraid of over lubricating the cases. You CAN spray too much (though it’s difficult), but it’s far better to use too much lube than not enough lube. Failure to use enough case lube will result in your case becoming stuck in the die. Getting a case stuck in a die is a nightmare scenario, so don’t do it! If you think you’ve got enough lube, go ahead and give the cases one more spray, just for good measure.

Once your brass is cleaned and lubed and you’ve got your resizing die properly adjusted and locked down as we discussed in our previous article, place your brass on the shell holder and lower the ram. You’ll begin to feel resistance as the expander ball is plunged through the neck of the case. One of the reasons that reloading necked brass is a bit easier than straight walled brass is that the dies for your necked down brass perform more operations with a single pull of the lever. The resizing die decaps the primer, resizes the brass, and expands the case neck to receive a new bullet, all in a single stroke.

Now that your brass has been resized, clean off the lubricant and inspect the brass for any cracks, creases, or bright spots near the head. A bright ring around the head at the base of the cartridge indicates stressed brass that will result in a case head separation. You may notice little dimples on your brass: this is not a big deal, and it occurs from using too much case lube. Large dimples occur when you have managed to use far too much lubricant. Brass with large dimples should be discarded.

In my experience, it is not usually necessary to measure and trim pistol brass after resizing. The same cannot be said about rifle cases. Use a dial caliper to ensure that all of your brass is the same correct length. You can also load the resized brass into your firearm to make sure it will chamber. Use a case trimmer to trim off any excess length.

Priming your rifle brass is the same procedure as priming your pistol brass. First, make sure that your primer pocket is cleaned out. Make sure that you have the correct size primer – large pistol and rifle primers can appear to be the same size, but they are not! Using the correct size tools and primers, prime all of your brass and make sure that the primers are seated to the proper depth. Primers that are set too high can be slam-fired in semiautomatic rifles.

When loading your powder, make sure that you have the right kind of powder. Using pistol powders in a rifle case can result in over-pressure and detonation, potentially destroying your rifle and injuring or killing you. It is very difficult (though not impossible) to double charge a rifle case if you are using the correct powders. Still, pay close attention. When developing a load, always double check your loads against a current reloading manual. Start at 50% of the manual’s recommended load and work up from there. Once you have a load developed, make sure to periodically check your powder measure against a scale to ensure that it remains consistent and accurate.

The final process in reloading rifle ammunition is seating and crimping the bullet. Since rifle cases are not flared, it can be more difficult to seat a flat based bullet. Boat tail bullets are much easier to seat. If you are loading flat based bullets, it helps to have a bevel cut in the case mouth using a chamfer or deburring tool. While crimping is not necessarily required for rifle rounds, it definitely helps when you are loading large caliber or magnum rounds. Crimping is definitely necessary if you are loading for a tube magazine fed rifle, as it will keep the bullets from being set back. Some bullet seating dies also crimp at the same time. Seat the first bullet, then measure your overall case length. Once you are certain the length is in spec, lock down your bullet seating die and proceed to seat bullets in the rest of your cartridges.

As always, observe proper safety procedures when reloading ammunition. Make sure that you have a clean and organized work area that is free from distractions. Never try to watch TV or listen to the radio while reloading – you’re working with potentially dangerous explosives that require 100% of your attention. Always wear proper eye protection when reloading. Remember that lead and primers are toxic and wash your hands every time after reloading.

The Mission of Cheaper Than Dirt!'s blog, The Shooter's Log, is to provide information—not opinions—to our customers and the shooting community. We want you, our readers, to be able to make informed decisions. The information provided here does not represent the views of Cheaper Than Dirt!

Comments (6)

  1. I am new to handle the guns like this. But since you are emphasizing here the steps to load a cartridge then I am very thankful that I get an idea for loading.

  2. Most books tell you to start at the bottom number and work up checking accuracy and if a semi auto/auto the cyccling of the weapon system as you go. decreasing the powder volume too much can also cause flash over that can cause a ka-boom as well. I always recccomend getting two to three recipes and compare them as to powder types and volumes, primers bullet types ect.. i have also found I will take the highest and lowest powder drop add them and devide by two and that seem to be the best set up for most of my pistol uses for each bullet weight…. also good to ahve a supply of factory ammunition for reach to compare when you are testing to have a baseline for feel accuracy ect. with pistol powders i like to use powders that will over flow the cases if double charged. that way you are less likely to fire a over charged case.when one startes reloading folks want to use the very fast powders with very low volumes to get real “cheap” with their loads its just not worth it remember “flash over”, “double charge” and worse “KA-BOOM!” get educated be careful and have fun reloading can and is very rewarding. D..

  3. I think your recommendation to start with loading 50% of a manuals recommendation does not read right. Don’t most manuals (like Hodgdon’s) specify a minimum and maximum load? and the minimum or starting load is more like 80% of the maximum.

    Aren’t there issues with below minimum charges other than having a bullet stick in the barrel? I have read of pressure problems but do not know the truth.

    Thank you for putting all this information together so cleanly.

    Edit: Nate, that’s a good point: it depends on the load, but your reloading manual should specify the minimum load. In some cases this is 50%, and in others it may be 60%, 75%, or 80%, depending on variables like powder type and case capacity. As always, information provided here is no substitute for the information found in your reloading manual.

Your email address will not be published. Required fields are marked *

Your discussions, feedback and comments are welcome here as long as they are relevant and insightful. Please be respectful of others. We reserve the right to edit as appropriate, delete profane, harassing, abusive and spam comments or posts, and block repeat offenders. All comments are held for moderation and will appear after approval.

Discover more from The Shooter's Log

Subscribe now to keep reading and get access to the full archive.

Continue reading