A few years ago, Ruger introduced a well made and nicely finished Government Model 1911 .45 ACP. The SR1911 has earned a reputation as an excellent value for its modest price. But Ruger did not stop there.
A few years later, Ruger introduced a Commander version. The standard Commander type—as currently manufactured by more than one maker—features a .75-inch shorter barrel than the 5-inch Government Model. The 4.25-inch barrel uses a standard barrel bushing. The frame is the same size as the Government Model. This all steel handgun handles well and clears leather faster than the Government Model.
The Lightweight (LW) Commander is a Commander length 1911 with an aluminum frame. This results in a considerable weight savings. A LW Commander weighs 28 ounces versus 40 ounces for the Government Model. Each of these variants uses a standard seven- or eight-round 1911 magazine.
The Officer’s Model is an even shorter variant. This pistol features a 3.6 inch barrel and a shortened grip frame. The Officers Model is a truly compact 1911 pistol. Due to the short slide and differences in geometry, the barrel must tilt at a more severe angle. The result is the barrel bushing is eliminated and the barrel is a bull type that butts into the frame for lockup. This design often results in excellent accuracy.
The original Officer’s Model was developed for use by General Officers in the United States Army. Colt introduced commercial versions to compete with compact pistols such as the Star PD—an excellent design. Ruger’s offering is chambered in 9mm Luger, banking on the immense popularity of the cartridge.
The new Officers Model 9mm SR1911 is an attractive handgun. The slide is satin finished nickel. The slide features Novak combat sights with a three dot outline. The slide lock, safety, magazine release, and beavertail safety are finished in black. The cocking serrations are the same unique slanted style used with the Ruger Commander.
The bushingless barrel is well fitted to the slide. A reverse plug caps off the recoil spring. The pistol features a stylish stepped slide that looks similar to the Browning P35, but it isn’t quite as sharply shouldered. The pistol doesn’t have a firing pin block or drop safety. Instead, it relies on a lightweight titanium firing pin and extra power siring pin spring for drop safety.
The frame is a dark gray hard anodized. The contrast with the slide is pleasing to the eye. The grips are among the best designed and feeling grips I have seen on a 1911. They are G10 material engraved with the Ruger logo. These thin grips allow the SR1911 Officers Model to maintain a low profile. I like the custom grade extended beavertail. This beavertail safety properly releases its hold on the trigger half way into trigger compression.
The pistol is delivered with two, well-designed and well-finished magazines. Trigger compression is a crisp 5.0 pounds without any rough spots or creep and modest take-up.
I lubricated the pistol over the long bearing surfaces before testing the Ruger Officers Model. During the initial work, I used a goodly amount of Winchester USA 115-grain FMJ ammunition. To test cycle reliability I also used the Winchester Defender 147-grain JHP loads. These loads have proven accurate and clean burning in a number of 9mm handguns. The Ruger 9mm was no exception.
I fired a box of each bullet weight without a single failure to feed, chamber, fire, or eject. There were no break-in malfunctions or short cycles. After this initial 150 rounds, I switched to the Winchester 124-grain PDX +P. This load demonstrates 1,200 fps in most pistols and just slightly less in the 3.6-inch barrel Officer’s Model.
This load offers excellent wound ballistics. This is a credible loading with good expansion and penetration. I fired these loads in rapid fire and the Ruger 9mm proved controllable, with well-centered groups at 7, 10, and 15 yards.
I field stripped and cleaned the pistol after the initial 260 rounds. There were no signs of eccentric wear. The pistol was lubricated along the long bearing surfaces. I returned to the range a few days later. To broaden the test I added a number of handloads using hard cast lead bullets.
If the pistol isnt reliable with cast lead bullets it may not have a place in my scheme of things. I also fired a number of Winchester’s 115-grain Silvertip. This is a popular load that demonstrates good wound potential. I elected to fire the piece for accuracy rom a solid bench rest. I fired at 15 yards in deference to the Ruger’s short barrel and sight radius. Accuracy was excellent as noted in the table below.
The 9mm 1911 Officer’s Model makes a lot of sense. This is a reliable, accurate, and controllable handgun. It is light enough for constant carry but heavy enough to control recoil. It rides close to the body but maintains a good firing grip.
|Sturm Ruger & Co. SR1911 Officers Model|
|Action:||Recoil-operated, hammer-fired, semi-automatic centerfire pistol|
|Sights:||Dovetailed three-dot configuration, drift adjustable|
|Overall Length:||7.25 inches|
I have carried my example with the Jeffrey Custom Leather EZ Carry for some weeks. This holster is a great inside the waistband holster but also offers the option of carrying the holster between the belt and the trousers. It is rigid enough for such use. This is a good kit, and the Ruger Officers Model is among the best carry guns to cross my desk in some time.
Which size 1911 do you prefer, Government, Commander, Officers? Are there any special upgrades or modifications you would recommend? Share your answers in the comment section.